Thinking about running wires next, what do I need to know? I have a modern universal 20 circuit panel, that I will likely put in the glovebox. I will likely reroute the engine bay stuff to clean it up as much as possible. Will be using stock dash switches (ign, fan, lights, wiper...) no power windows, no electric fan, no ac, no crazy stereo. MSD box will be in the glove box as well. Thinking about changing everything external to weatherpacks (would be nice if someone had a complete list of external connectors with # of pins for each). Anyone have a good schematic?
-
Hello there guest and Welcome to The #1 Classic Mustang forum!
To gain full access you must Register. Registration is free and it takes only a few moments to complete.
Already a member? Login here then!
Starting Wiring, what do I need to know?
- Thread starter 65-408
- Start date
I used a generic harness with the 20 mini fuses and was able to install it close to the original location. It sounds like you are going to have a lot of leftover wires... Are you going to pare it down some? It's amazing how all those extra wires take up space when you don't have any need for them.
The Painless manuals are pretty good for highlighting things that aren't covered in the original schematics.
[pdf]http://www.painlesswiring.com/Manuals/20120.pdf[/pdf]
As for as weatherpack connectors, about the only place I think I should have used them is on the front parking lights and the backup light. Otherwise, just about everything else had a factory style connector that is weatherized from what I recall.
On the firewall, I placed holes on both ends to feed wires to the respective side of the engine compartment to minimize wires spanning across the bay. On my chebby, I added a 3rd hole close to the bellhousing to run the starter solenoid wire, oil pressure line, temp sensor wire, choke power and ignition power.
One thing I did that worked out well is I had a full chassis harness from an '89 mustang and from that I cut every pair of male / female connector with about 12" of wire so that I could make cleaner splits. I suppose thats what you plan for the weatherpack connectors, but these were free to me and usually the pick and pull will only charge a buck or two if you need more.
Are you using a stock column or a replacement that uses the stock GM connector... the bonus there is you get to take advantage easily adding hazard lights.
The Painless manuals are pretty good for highlighting things that aren't covered in the original schematics.
[pdf]http://www.painlesswiring.com/Manuals/20120.pdf[/pdf]
As for as weatherpack connectors, about the only place I think I should have used them is on the front parking lights and the backup light. Otherwise, just about everything else had a factory style connector that is weatherized from what I recall.
On the firewall, I placed holes on both ends to feed wires to the respective side of the engine compartment to minimize wires spanning across the bay. On my chebby, I added a 3rd hole close to the bellhousing to run the starter solenoid wire, oil pressure line, temp sensor wire, choke power and ignition power.
One thing I did that worked out well is I had a full chassis harness from an '89 mustang and from that I cut every pair of male / female connector with about 12" of wire so that I could make cleaner splits. I suppose thats what you plan for the weatherpack connectors, but these were free to me and usually the pick and pull will only charge a buck or two if you need more.
Are you using a stock column or a replacement that uses the stock GM connector... the bonus there is you get to take advantage easily adding hazard lights.
"stangg" said:
thanks, that will help alot along with the original schematics that I found here:
http://averagejoerestoration.com/resour ... -diagrams/
more to it than I thought... maybe I will put this off, not sure I am mentally prepared to start this...
70_Fastback
Hell Bent for Speed
When I wired the rat rod from scratch, it was very simple. One thing I would recommend is to ditch the Ford alternator with external regulators, etc and convert to a GM 1-Wire unit. That's I did. Very, very simple to do. I can get you the model number if you would like - but I believe it's a 70-Amp unit. And I am even running an E-fan as well.